Doors are essential for every family and play an important role in our safety. Therefore, the requirements for fire doors have been very strict. As a new type of door, wooden fire doors are high-tech products. Wooden fire doors can not only beautify our home, but also add points for our home safety. Let's take a look at the attractive quality of the fire-proof board of fumika?

　　防火板有豐富的外觀紋理可供選擇，木紋素色金屬可用。在裝飾分中，必須考慮的是裝飾的風格是一體性的，傳統的防火門不使用防火板，保證難一體性的風格。所以當室內裝修用了某種外觀紋路的紋路后，我們可以找與室內紋路相同的防火板用來做防火門，防火門的銷售商這樣說。

　　The fire-proof board has rich appearance texture to choose from, and the wood grain plain color metal is available. In the decoration, we must consider that the style of decoration is integrated. The traditional fire door does not use fire-proof board to ensure the style of difficult integration. So when the interior decoration with a certain appearance of the lines, we can find the same lines with the interior of the fire board to do fire doors, fire door vendors say so.

　　二、富美家防火板可阻燃防潮、防蟲、施工簡單、不褪色、不甲醛。

　　2、 Fumeijia fire-proof board can be flame-retardant, moisture-proof, insect proof, simple in construction, colorfast and formaldehyde free.

　　防火門關鍵點:

　　Key points of fire door:

　　(1)線。根據規劃要求的比例、高程和方向，繪制出木質防火門門框方位角線。

　　(1) Line. According to the scale, elevation and direction required by the planning, draw the azimuth line of wood fire door frame.

　　(2)設置門框。先拆下木質防火板門框門框下方的固定板，每一門框內的高度比門的高度大30毫米，洞口兩側的地面必須設置預留槽。門框一般埋設在±0.00 20mm標高以下，門框開口的上、下尺寸必須相同。允許誤差< 1.5mm，對角線允許誤差< 2mm。木質防火門門框用木楔臨時固定在洞口，經校對合格后，木楔、門框鐵腳與嵌入的鐵板焊接牢固。

　　(2) Set the door frame. First remove the fixed plate under the door frame of the wooden fire-proof board. The height of each door frame is 30mm higher than the height of the door. The ground on both sides of the hole must be provided with reserved slots. The door frame is generally buried below the elevation of ± 0.00mm, and the upper and lower dimensions of the door frame opening must be the same. The allowable error is less than 1.5mm, and the allowable error of diagonal is less than 2mm. Wooden fire door frame shall be temporarily fixed at the opening with wooden wedge. After being checked to be qualified, wooden wedge, iron foot of door frame and embedded iron plate shall be welded firmly.

　　(3)設備門及附件。木質防火板門門框周圍的裂縫應采用1:2水泥砂漿或強度不小于10MPa的細石混凝土牢固嵌固，保證與墻體形成整體;固化冷凝后，重新油漆孔和墻面。涂裝后，設備門、五金配件及相關消防設備。門關閉后，門縫應均勻，打開時應輕松輕便，不得有過緊、過松和回彈現象。

　　(3) Equipment door and accessories. 1:2 cement mortar or fine aggregate concrete with strength no less than 10MPa shall be used to firmly embed the cracks around the door frame of wooden fire-proof panel door to ensure the integrity with the wall; after solidification and condensation, paint the holes and walls again. After painting, equipment doors, hardware accessories and related fire fighting equipment. After the door is closed, the door joint shall be even, and it shall be easy and light to open without over tightening, over loosening and rebound.

　　以上是富美家防火板制造商為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.0473114.cn

　　The above is the related content introduced by the manufacturer of fumeijia fire board. For more information, please visit the website: http://www.0473114.cn