抗倍特被廣泛用于學校實驗室、醫院等，那么在使用抗倍特時應該注意哪些問題？下面小編為您整理總結了八點，一起來看看。

Anti beta is widely used in schools, laboratories, hospitals, etc., so what should be paid attention to when using anti beta? The following editor summarizes eight points for you. Let's have a look.

1、抗倍特應存放在陰涼干燥場地，避免陽光直射和直接放在地面上，避免受潮。存放條件是18-25℃，相對濕度45-55%，存儲時間不超過6個月。

1. Kangbeite should be stored in a cool and dry place, away from direct sunlight and directly on the ground to avoid moisture. The storage condition is 18-25 ℃, relative humidity 45-55%, and the storage time shall not exceed 6 months.

2、抗倍特加工前一定要清除工作臺面的異物，以避免板材在拖拉、裁切時造成劃傷，不能使用尖銳物品刮拭保護膜表面。

2. Before anti Beite processing, the foreign matters on the worktable must be removed to avoid scratches caused by dragging and cutting the plate. Sharp objects cannot be used to wipe the surface of the protective film.

3、抗倍特裁切時需沿長度方向裁切，以保證板材拼接時的同向拼接。

3. It needs to be cut along the length direction when cutting anti Beite, so as to ensure the same direction splicing when splicing plates.

4、抗倍特抗倍特在裁切加工時，如果有雙面保護膜的必須將雙面保護膜同時保留或者同時撕去，以保證產品兩面受環境因素的影響程度一致。如僅僅保留單面保護膜，則一定要用PVC類薄膜對板材以及半成品加以包裹。

4. When cutting, if there is a double-sided protective film, the double-sided protective film must be kept or torn off at the same time to ensure that both sides of the product are affected by environmental factors. If only one-sided protective film is retained, the sheet and semi-finished products must be wrapped with PVC film.

5、抗倍特保證堆放整齊，尺寸小的板材疊于尺寸大的上面，以維持受力的均衡，臺面做好假厚以后，堆放時中間放置適當同樣厚度的邊條墊實，避免板材受力不均勻。

5. Kangbeite ensures that the plates with small size are stacked neatly on the plates with large size, so as to maintain the balance of stress. After the false thickness of the table is made, the edge strips with the same thickness are placed in the middle of stacking to avoid uneven stress of the plates.

6、抗倍特成品和半成品在包裝或存放時，底部和頂部分別使用墊板和蓋板，以隔絕潮濕空氣對上下板子單面的影響，防止產生翹曲。

6. When anti Beite finished products and semi-finished products are packed or stored, base plates and cover plates are used at the bottom and top respectively to isolate the influence of moist air on one side of the upper and lower plates and prevent warpage.

7、抗倍特使用于實驗室臺面的安裝時，必須使用螺絲固定法，同時每間隔80cm使用直角五金固定，并采用直徑5mm左右的平頭螺絲固定直角五金，鉆孔采用帶限的槍鉆，以防止鉆孔深度過大，穿透表面。到工地后應盡快安裝，安裝結束后應立刻撕去耐火板表面的保護膜，否則在長時間下容易產生受力不均而變形。

7. When anti Beite is used for the installation of the laboratory table, it must use the screw fixation method. At the same time, it must use the right angle hardware to fix every 80cm, and use the flat head screws with a diameter of about 5mm to fix the right angle hardware. The limited gun drill is used for drilling to prevent the drilling depth from being too large and penetrating the surface. After arriving at the construction site, it should be installed as soon as possible. After installation, the protective film on the surface of the refractory board should be immediately removed, otherwise it is easy to produce uneven stress and deformation for a long time.

8、富美家抗倍特在取用時，一定要兩人以上同時抬取，避免在產品表面的拖動和碰撞，防止表面劃傷和邊角破損。

8. When taking fumeijia kangbeite, two or more people must lift it at the same time to avoid dragging and collision on the surface of the product and prevent surface scratches and corner damage.

以上就是問題解答的相關內容了，希望能夠幫助到大家，如對這一問題還存在任何疑問，都?xì)g迎關注我們網站http://www.0473114.cn并咨詢我們的工作人員，將竭誠為您服務。

The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.0473114.cn And consult our staff, will serve you wholeheartedly.